FX Australia® Product Information

NEW FX Soap Wax Natural & FX Liquid Wax Natural

(Interior Only)

New NATURAL FX Soap Wax and FX Liquid Wax are specifically formulated to dramatically highlight the patterns and textures of FX Stucco coatings, FX Marmorino and FX Travertino®, producing varied creative finishes. These wax products are also used to protect FX Stucco coatings against wear and moisture in high traffic areas. FX Liquid Wax, tinted or untinted, is also ideal to create a French Provincial look on furniture pieces when used over FX Milk Paint.

Product Description



Attractive finishes

Varied effects



Easy spreading

Ease of application 


FX Soap Wax and FX Liquid Wax are ideal for adding further creative effects to FX Stucco, FX Marmorino and FX Travertino® coatings, and protecting these finishes.

Surface Preparation

Before applying any FX wax product over base FX Stucco, FX Marmorino or FX Travertino® coat, ensure the surface is free of dirt and dust. There should be no grease or stains. Any efflorescence or mould should have been treated beforehand at the initial preparation stages before applying FX Stucco Undercoat. See appropriate FX Product Information Sheets.



Place a small amount of wax (the size of a twenty-cent coin) onto the centre of a stainless-steel trowel. Move trowel over the surface leaving a fine film of wax on the surface. Then go back over the area with a clean trowel, removing any unwanted or excess wax, and burnishing the surface. Work one square metre area at a time. Once satisfied that the area is waxed correctly, allow to dry completely. Then polish with a clean white rag or lamb's wool buffer.

Alternatively, FX Soap Wax may be applied as per the instructions for FX Liquid Wax. See information below.


Place a small amount of FX Liquid Wax onto a clean white rag. Apply product in a circular motion. As the liquid wax penetrates the surface, continue to buff with the razor alternatively, wait until the wax is completely dry then polish with a lamb's wool buffer.

Conventional Spray:

Not suitable for use with spray equipment.

Approximate Spreading Rate: FX Soap Wax & FX Liquid Wax:

Depends on application technique and surface roughness.

Approximate Film Thickness per coat:

Wet: 100 Microns; Dry: 10 Microns.


1 coat for a simple wax finish.


Not required.


Both products may be tinted. Refer to colour chart for tinting specification.


FX Soap Wax: Trowel, or clean white cotton rag; FX Liquid Wax: clean white cotton rag.

Drying Times (at 25 °C): Touch: (at 25 °C): Touch: 1-2 Hours; Recoat: If required, 2-4 Hours.

Clean-up: Warm soapy water. Safety: Dust Mask. Gloss Level: N/A.

Note: Do not apply paint if the air temperature or substrate temperature is below 10 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process.

Safety and Environmental Care


Personal Protection:

Wear eye protection and dust mask when spraying, as splashes may cause eye irritation and inhalation of spray mist may cause respiratory irritation.

Asbestos cement sheeting:

Do not disturb, sand or scrub, and avoid any peripheral dust. If you do not have professional expertise in the handling/removal of asbestos sheeting, use a licensed asbestos removalist.

Refer to product labels, current FX Australia Safety Data Sheets or call FX Australia for detailed information.


Slippery when spilled·

Restrict access to area until clean-up is completed · When cleaning up spills, use personal protection equipment · Stop leak if safe to do so and contain spill with absorbent material such as sand, vermiculite or other inert material · Prevent spill from entering waterways · Collect and dispose of spilled material according to local regulations · Wash away remnants with liberal amounts of cold water.


Store in a cool, dry, well-ventilated place out of direct sunlight · Store away from strong acids and moisture · Keep containers closed at all times and check regularly for spills.


Refer to State/Territory Land Waste Management Authority: most authorities permit disposal at approved land waste sites.

Date of Issue: November  2018

About Us

Australian manufacturer of premium quality speciality paints, architectural & protective coatings and a range of innovative joint & topping compounds.

FX Australia is proudly Australian-owned and Australian-made. We’ve created unique, award-winning paint and plaster finishes for local and international top-drawer brands and design teams and turned many a professional’s concept into reality.


Read More


We'd love to
hear from you.

© 2018 by NF Designs & FX Australia. Proudly created with Wix.com